for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 1 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz general description features functional diagram passive double-balanced topology input ip3: +18 dbm low conversion loss: 6.5 db lo / rf isolation: 30 db lo / if isolation: 25 db upconverter & downconverter applications electrical specifcations, t a = +25 c, as a function of lo drive typical applications the HMC218AMS8E is ideal for: ? basestations, repeaters & access points ? wimax, wibro & fixed wireless ? portables & subscribers ? plmr, public safety & telematics the HMC218AMS8E is an ultra miniature double-bal - anced mixer in an 8 lead plastic surface mount pack - age (msop). this passive mmic mixer is constructed of gaas schottky diodes and novel planar trans - former baluns on the chip. the device can be used as an upconverter, downconverter, biphase modulator / demodulator, or phase comparator. the low conver - sion loss, high isolation and wide if bandwidth make this mixer ideal for a variety of rx and tx frequency plans. parameter lo = +13 dbm if = 100 mhz lo = +10 dbm if = 100 mhz lo = +7 dbm if = 100 mhz units min. typ. max. min. typ. max. min. typ. max. frequency range, rf & lo 4.5 - 6.0 4.5 - 6.0 4.7 - 5.9 ghz frequency range, if dc - 1.6 dc - 1.6 dc - 1.5 ghz conversion loss 6.5 8.5 8 9.5 8 9.5 db noise figure (ssb) 6.5 8.5 8 9.5 8 9.5 db lo to rf isolation 25 30 25 30 23 28 db lo to if isolation 15 25 14 25 12 23 db ip3 (input) 5.2 ghz 5.8 ghz 12 15 16 18 11 13 14 17 9 10 12 13 dbm 1 db gain compression (input) 7 10 5 9 4 7 dbm
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 2 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz conversion loss vs temperature @ lo = +13 dbm isolation @ lo = +13 dbm conversion loss vs. lo drive return loss @ lo = +13 dbm if bandwidth @ lo = +13 dbm p1db vs. temperature @ lo = +13 dbm -20 -15 -10 -5 0 3.5 4 4.5 5 5.5 6 6.5 -40 c +25 c +85 c conversion loss (db) frequency (ghz) -20 -15 -10 -5 0 3.5 4 4.5 5 5.5 6 6.5 +5 dbm +7 dbm +9 dbm +11 dbm +13 dbm conversion loss (db) frequency (ghz) -25 -20 -15 -10 -5 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 conversion loss (db) if frequency (ghz) -60 -50 -40 -30 -20 -10 0 3.5 4 4.5 5 5.5 6 6.5 rf/if lo/if lo/rf isolation (db) frequency (ghz) -35 -28 -21 -14 -7 0 0123456 rf if lo return loss (db) frequency (ghz) 6 7 8 9 10 11 12 4.8 5 5.2 5.4 5.6 5.8 6 -40 c +25 c +85 c p1db (dbm) frequency (ghz)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 3 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz input ip3 vs. temperature @ lo = +13 dbm input ip2 vs. temperature @ lo = +13 dbm input ip3 vs. lo drive input ip2 vs. lo drive 12 14 16 18 20 22 4.8 5 5.2 5.4 5.6 5.8 6 6.2 +9 dbm +11 dbm +13 dbm ip3 (dbm) lo frequency (ghz) 30 40 50 60 70 4.8 5 5.2 5.4 5.6 5.8 6 +9 dbm +11 dbm +13 dbm ip2 (dbm) lo frequency (ghz) 14 16 18 20 22 4.8 5 5.2 5.4 5.6 5.8 6 6.2 -40 c +25 c +85 c ip3 (dbm) lo frequency (ghz) 30 40 50 60 70 4.8 5 5.2 5.4 5.6 5.8 6 -40 c +25 c +85 c ip2 (dbm) lo frequency (ghz)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 4 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz absolute maximum ratings rf / input +13 dbm lo drive +27 dbm storage temperature -65 to +150 c operating temperature -40 to +85 c electrostatic sensitive device observe handling precautions mxn spurious outputs harmonics of lo nlo mrf 0 1 2 3 4 0 xx 1 10 22 35 1 8 0 37 29 54 2 67 60 58 58 77 3 >85 79 79 59 77 4 >85 >85 >85 >85 >85 rf = 5.15 ghz @ -10 dbm lo = 5.25 ghz @ +13 dbm all values in dbc relative to the if lo freq. (ghz) nlo spur at rf port 1 2 3 4 5.0 32 26 50 69 5.2 32 28 55 71 5.4 33 32 54 75 5.6 33 33 55 69 5.8 33 32 56 62 6.0 32 34 57 58 lo = +13 dbm values in dbc below lo level measured at rf port.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 5 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz outline drawing notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. dimension does not include moldflash of 0.15 mm per side. 4. dimension does not include moldflash of 0.25 mm per side. 5. all ground leads must be soldered to pcb rf ground. part number package body material lead finish msl rating package marking [2] HMC218AMS8E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [1] h218a xxxx [1] max peak refow temperature of 260 c [2] 4-digit lot number xxxx package information
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com mixers - dbl-bal - smt 9 0 - 6 HMC218AMS8E v 0 0.0 411 gaas mmic smt double- balanced mixer, 4.5 - 6 ghz evaluation pcb list of materials for evaluation pcb 101830 [1] item description j1 - j3 pcb mount sma rf connector u1 HMC218AMS8E mixer pcb [2] 101828 evaluation board [1] reference this number when ordering complete evaluation pcb [2] circuit board material: rogers 4350 the circuit board used in the application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from hittite upon request.
|
